specialised tractor for grass cutting

[KIWINZ]

a few of you would of seen this topic earlier but when gav said they have threatened with legal action in the past i thought i wuld remove it and start again with no sign of that cirtian company tell me what you think!!!

firstly the front

then the main thing

the whole thing folded up

un folded for work

the idea is to have the front topper hanging out above the ditch bank and the trimmer head on the bank

[FB]

looks good!! :) , dont see what they would do if your keeping the model , if you sold them, that would be a different story \ \

[KIWINZ]

need to get a new camera these are done on my w810i walkman phone in need of some T.L.C so are therefore rubbish

[JC]

a few of you would of seen this topic earlier but when gav said they have threatened with legal action in the past i thought i wuld remove it and start again with no sign of that cirtian company tell me what you think!!!

Looks Good. 

Tell me more about the prosecution bit then?

[Johny mf]

looks good to me

but i begin to wonder how you can get i the cab

[Kiwi6920]

Looks good mate, nice work

[KIWINZ]

Looks Good. 

Tell me more about the prosecution bit then?

the first one had a hyperlink to the mcconnel website with the new PA800M (under new products) gav told me to be carefull as in the past people doing the similar thing to me had been threatend with legal action. not wanting to get in to any trouble i removed it allthough it was for more the picture not for a copy of there product so you lot could see what its meant to look like against my attempt

[KIWINZ]

looks good to me

but i begin to wonder how you can get i the cab

the tractor has two doors!!!

[Tractorman810]

looks good to me

but i begin to wonder how you can get i the cab

in real life the mesh would be fitted to the door so it would still open mate, its a bit difficult to achevie in 1/32 though as they dont do to much in the way of fine detail mesh like that

[JC]

the first one had a hyperlink to the mcconnel website with the new PA800M (under new products) gav told me to be carefull as in the past people doing the similar thing to me had been threatend with legal action. not wanting to get in to any trouble i removed it allthough it was for more the picture not for a copy of there product so you lot could see what its meant to look like against my attempt

It sounds a bit OTT to me, it's not as if you are stealing anything from them or making a profit at their expense so I wouldn't worry too much mate. 

[Massey Boy]

It sounds a bit OTT to me, it's not as if you are stealing anything from them or making a profit at their expense so I wouldn't worry too much mate. 

if they do take legal action just say no one would souply me with the paint to paint it

[Johny mf]

the tractor has two doors!!!

i know that but most off the time the gear leavers are on the right side off the cab and its hard to get in from that side!

I drove one time a 6920s and it where verry dificult to get in from the right side off the cab!

(needed to get in from that side because sombody parked it against the wall Stupid person that where!)

[rich.new holland]

the only critisism  is that you are rolling the grass before you are cutting it  apart from that it looks exactly like the one that came  round my mates farm  cutting before    you got the same phone as me  i got a white one 

[sparrow legs]

looks very good, well done, nice work . often looked at these rigs and thought what would it be like to drive one? ie operating 2 flails at once yes it can be done but to what sort of standard?? i know of rigs like this but the drivers use one or the other at any one time, not both together, i have thought of a front topper on my flailing tractor but adds to the length and would make corner hard to flail out

[MJB1]

some chaps do opperate both at the same time , they have a jocky wheel on the front of the topper fitted to a sensor, when a rise in the ground occurs the sensor lifts the topper till the obstruction has gone or the ground levels out  but then most of this sort of work is the straight forward motorway or dual carridge way work

the standen statesman tow i used to use was fitted with this type of sensor switch for harvesting parsnips

[Powerstarâ„¢]

I like it,apart from the mesh  \

If you go in to your local DIY store you can get fine mesh that is used to patch up holes on things and filler it over, that painted black would look far better.

But on the whole, I like it!

[Kiwi6920]

Looks good, looks very simlar to the renualt set up i got just one dodgy pic of when i was down south, ill  find it and chuck it up for you

[KIWINZ]

I like it,apart from the mesh  \

If you go in to your local DIY store you can get fine mesh that is used to patch up holes on things and filler it over, that painted black would look far better.

But on the whole, I like it!

thanks i dont really go neer the DIY store very often but ill ask me mum!!!

Looks good, looks very simlar to the renualt set up i got just one dodgy pic of when i was down south, ill  find it and chuck it up for you

thanks

and thanks all its nice to get some constructuve critisim and input from others