Niels Posted July 13, 2014 Share Posted July 13, 2014 That looks very nice! Lot of hours must have gone into that model. Does the levelling work like on the real thing? If I could have a little criticism I'd say the cab glass and layout are New Holland? The glass is much more curved than on the Vista. Other than that well done. I see the stairs are seperate and you have to weld them on yourself? 1 Quote Link to comment Share on other sites More sharing options...
towse trading Posted July 14, 2014 Share Posted July 14, 2014 That looks very nice! Lot of hours must have gone into that model. Does the levelling work like on the real thing? If I could have a little criticism I'd say the cab glass and layout are New Holland? The glass is much more curved than on the Vista. Other than that well done. I see the stairs are seperate and you have to weld them on yourself? no the leveling dose not work , yes nh cab , could not find a good cab to use to keep the costs down , did not justify breaking a claas up , i used the nh axle hubs for the rear axle , no steps are cut out of mesh , but fitted loosed as they will get bend in the packing of the model. dave Quote Link to comment Share on other sites More sharing options...
towse trading Posted July 16, 2014 Share Posted July 16, 2014 track unit made and cast , added to model no 2 . Quote Link to comment Share on other sites More sharing options...
bay Posted July 19, 2014 Share Posted July 19, 2014 John Deere 2140 from ertl chassis, just awaiting decals, scania t cab, scania 143m Britain's 3650 will be here on Monday to get the works, attic bulk tipper 5 Quote Link to comment Share on other sites More sharing options...
Stabliofarmer Posted July 19, 2014 Share Posted July 19, 2014 Loving the sounds of all of them Mark, particularly the 143 1 Quote Link to comment Share on other sites More sharing options...
bay Posted July 20, 2014 Share Posted July 20, 2014 thanks James, it could be a while before its done, got alot to get done for folk first,got some of the cab built Quote Link to comment Share on other sites More sharing options...
Jordan_coe2012 Posted July 29, 2014 Share Posted July 29, 2014 An artic tanker, haven't made my mind up yet as to what it will be just yet! 1 Quote Link to comment Share on other sites More sharing options...
Tractorman810 Posted August 27, 2014 Share Posted August 27, 2014 not on my normal workbench as that's still being used for work in the garden, but on my portable(big pansy go indoors when its cold board ) managed to get my pma trailer kit assembled/test built, have gone for smaller uh vanto wheels on it, the ones it came with were to big, not decided on colour yet, but it will have a set of removable grain extensions built for it, more than likely wooden ones with metal frame ,the rear lower panel will get a grain door with rubber shoot so it can still drop when required .the kit is very well made, and scales to a 7/8 ton trailer , it appears to be 3 d printed as I can not see any resin over runs etc on it , the ram will be altered to a more uk looking one, as its not supplied with a working ram, and the one that is is a much more euro spec one ,very short multi stage that pushed up backwards as ,not decided on whether I will buy the hay extensions and ladders yet, but the bed has the holes for them , so it would make a very nice multi use trailer on the layout 4 Quote Link to comment Share on other sites More sharing options...
catkom3 Posted August 27, 2014 Share Posted August 27, 2014 Very nice Sean,do the parts have a rough pitted surface,if they do then defo 3D printed,it's the nature of the process,you can smooth out the finish,but that looks a bit dodge,which I reckon would leave a surface very difficut to paint,see here, http://www.youtube.com/watch?v=Jv-CbnB8Uz4 Regards Joe. Quote Link to comment Share on other sites More sharing options...
roberthenning Posted August 27, 2014 Share Posted August 27, 2014 What do you think of that kit Sean? I was thinking of getting two to mid for my redrock and weeks builds world save me a load of scratch building. Quote Link to comment Share on other sites More sharing options...
Tractorman810 Posted August 27, 2014 Share Posted August 27, 2014 joe its not a rough finish, but it is ever so slightly pitted, the holes etc are all in place and ?? well it looks printed to me . only way I could see it done looking at the detail on the parts, like the handbrake lever its a very nice kit actually Robert, tad European, well its French, but not a lot of work required to get it more uk looking, ,had a real good look and it was to much to get a wooden floor and sides, ,but as you say with a bit of sanding you could make it a close weeks . I may well get another at Zwolle but get a second axel for it Quote Link to comment Share on other sites More sharing options...
roberthenning Posted August 27, 2014 Share Posted August 27, 2014 Yeah all I think is different sides made up will do a weeks. Did you just have the uh wheels spare as they're the same as on my redrock, the weeks wee have has double lorry wheeled single axel that dad put in it so it could actually take a load of spuds Quote Link to comment Share on other sites More sharing options...
catkom3 Posted August 27, 2014 Share Posted August 27, 2014 Yes,that's what I meant Sean,pitted,it's the way the resin layers are built up. Regards Joe. Quote Link to comment Share on other sites More sharing options...
Stabliofarmer Posted September 24, 2014 Share Posted September 24, 2014 Rubber casting, some new fancy truck wheels ready for my Scania Quote Link to comment Share on other sites More sharing options...
Jd6320driver Posted September 24, 2014 Share Posted September 24, 2014 Baby donkey and a massey 390t 2wd 1 Quote Link to comment Share on other sites More sharing options...
Jd6320driver Posted September 24, 2014 Share Posted September 24, 2014 not on my normal workbench as that's still being used for work in the garden, but on my portable(big pansy go indoors when its cold board ) managed to get my pma trailer kit assembled/test built, have gone for smaller uh vanto wheels on it, the ones it came with were to big, not decided on colour yet, but it will have a set of removable grain extensions built for it, more than likely wooden ones with metal frame ,the rear lower panel will get a grain door with rubber shoot so it can still drop when required .the kit is very well made, and scales to a 7/8 ton trailer , it appears to be 3 d printed as I can not see any resin over runs etc on it , the ram will be altered to a more uk looking one, as its not supplied with a working ram, and the one that is is a much more euro spec one ,very short multi stage that pushed up backwards as ,not decided on whether I will buy the hay extensions and ladders yet, but the bed has the holes for them , so it would make a very nice multi use trailer on the layout I have had a slurrykat front reel 3d printed and would advise rubbing down before primer and then your desired top coat Quote Link to comment Share on other sites More sharing options...
11johndeereman Posted September 25, 2014 Share Posted September 25, 2014 Too much ford tw15 ford tw35 john deere 3650 ford 7840 grain crimper watson feeder trailer 1 Quote Link to comment Share on other sites More sharing options...
PDC Posted September 27, 2014 Share Posted September 27, 2014 Knocked these up today. 5 Quote Link to comment Share on other sites More sharing options...
Jd6320driver Posted September 27, 2014 Share Posted September 27, 2014 I think it is the Massey 390 axle Quote Link to comment Share on other sites More sharing options...
PDC Posted September 28, 2014 Share Posted September 28, 2014 I've been working on these today 1 Quote Link to comment Share on other sites More sharing options...
Paul Palmer Posted September 28, 2014 Share Posted September 28, 2014 what have you done to the jd's Paul i can see one has rear duals Quote Link to comment Share on other sites More sharing options...
PDC Posted September 28, 2014 Share Posted September 28, 2014 3650 with rear duals new beacon and front weights 2 Quote Link to comment Share on other sites More sharing options...
PDC Posted September 28, 2014 Share Posted September 28, 2014 3650 with UH valtra T wheels 3 Quote Link to comment Share on other sites More sharing options...
PDC Posted September 28, 2014 Share Posted September 28, 2014 (edited) 3350 with UH front linkage Edited September 28, 2014 by PDC 2 Quote Link to comment Share on other sites More sharing options...
Paul Palmer Posted September 28, 2014 Share Posted September 28, 2014 got you ,they look great,so the 3650 doesnt come with weights? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.